Diagnóstico P0016, P0017, P0087, P0088 en Mercedes-Benz E-Class 2016 2.0
Códigos P0016, P0017, P0087 y 2 más en Mercedes-Benz E-Class 2016: síntomas, causas y verificaciones por ChatMecano.
Síntomas observados
Filter Function
Códigos OBD2 detectados
- P0016 — Corrélation vilebrequin - Arbre à cames (Banc 1 capteur A)
- P0017 — Code de défaut diagnostic standard constructeur
- P0087 — Pression de rampe commune carburant trop basse
- P0088 — Pression de rampe commune carburant trop haute
- P0191 — Code de défaut diagnostic standard constructeur
Análisis y verificaciones de ChatMecano
Las notas técnicas reproducen el expediente original; algunos extractos pueden conservar el idioma introducido por el usuario.
Likely Diagnosis
The distinct, rhythmic, and steady abnormal sound emerging at 2,000 RPM and intensifying with engine speed, while in neutral, points to a rotating component issue directly linked to engine operation. Common sources include:
- Accessory drive system component failure (idler pulley, tensioner, alternator, water pump, A/C compressor, power steering pump bearings).
- Vacuum pump internal wear.
- Timing chain or timing chain tensioner issue.
- Turbocharger bearing wear or impeller contact.
Diagnostic Procedure
- Pinpoint noise origin: Use a mechanic's stethoscope to localize the sound to a specific engine area.
- Accessory belt test:
- Mark serpentine belt direction.
- Remove serpentine belt.
- Start engine briefly (max 30 seconds) and rev to 2000 RPM to check if noise persists.
- If noise stops, the issue is in an accessory component.
- Inspect accessory components (if noise stops with belt removed):
- Manually spin each pulley: idler pulleys, tensioner pulley, alternator, water pump, A/C compressor, power steering pump.
- Check for rough bearings, excessive play, or grinding.
- Inspect serpentine belt for cracks, fraying, or glazing.
- Inspect vacuum pump (if noise persists with belt removed or localized to cylinder head):
- Use stethoscope to listen specifically to the vacuum pump.
- Check for external oil leaks around the vacuum pump.
- Timing chain/tensioner inspection (if other sources ruled out):
- Remove valve cover.
- Inspect for timing chain slack, especially between camshaft sprockets.
- Check timing chain tensioner for proper extension and signs of failure.
- Inspect timing chain guides for wear or breakage.
- Turbocharger inspection (if other sources ruled out and noise localized to turbo):
- Remove intake pipe from turbocharger.
- Check for excessive shaft play (radial and axial).
- Inspect compressor wheel for signs of contact with housing.
Torques & Specifications
- Serpentine belt tensioner bolt: 50 Nm / 37 lb-ft.
- Idler pulley bolt: 25 Nm / 18 lb-ft.
- Vacuum pump mounting bolts: 25 Nm / 18 lb-ft.
- Valve cover bolts: 9 Nm / 6.6 lb-ft.
- Timing chain tensioner: 80 Nm / 59 lb-ft.
OEM Parts / References
- Serpentine belt: Mercedes-Benz A0019931796 (ref to verify).
- Belt tensioner: Mercedes-Benz A2742000270 (ref to verify).
- Idler pulley: Mercedes-Benz A2742020019 (ref to verify).
- Vacuum pump: Mercedes-Benz A2742300065 (ref to verify).
- Timing chain kit (chain, guides, tensioner): Mercedes-Benz A2740500116 (ref to verify).
Common Pitfalls & Known TSBs
- M274 Timing Chain Stretch: Mercedes-Benz M274 engines are known for timing chain stretch at higher mileages, leading to rattling or ticking noises, potentially triggering P0016/P0017 codes.
- Vacuum Pump Failure: The vacuum pump on the M274 engine can develop internal wear, producing rhythmic knocking or ticking sounds.
- Accessory Drive Component Bearing Failure: Common wear item, often identifiable with a stethoscope or by spinning pulleys manually.
- TSB LI03.30-P-062835: Addresses rattling noises from the timing chain area on M274 engines, recommending timing chain and tensioner inspection.
Estos ejemplos ayudan a orientar el diagnóstico. No confirman una falla en tu vehículo: verifica las mediciones y especificaciones del fabricante antes de reparar.