P0120, P0121 diagnostic on Yamaha Aerox 2021 155cc
P0120, P0121 on a Yamaha Aerox 2021: real symptoms, code definitions, likely causes and step-by-step priority checks documented by ChatMecano.
Observed symptoms
Coolant Function
OBD2 codes detected
- P0120 — Code de défaut diagnostic standard constructeur
- P0121 — Capteur de position papillon / pédale A - Plage / rendement
ChatMecano analysis and checks
Technical notes are reproduced from the original case file; some excerpts may remain in the language entered by the user.
TPS Verification and Adjustment Procedure
After verifying the static TPS voltage parameters, perform a dynamic check.
- Use a diagnostic scanner to monitor live TPS voltage and throttle percentage while slowly rotating the throttle grip from closed to wide open.
- Ensure voltage increases smoothly without drops, spikes, or dead spots.
- Verify throttle percentage corresponds accurately to the physical throttle plate position throughout the range.
- If the TPS is adjustable (some Yamaha models allow slight rotation), loosen the retaining screws and rotate the sensor body to achieve the correct Closed Throttle Position (CTP) voltage.
- Re-tighten TPS retaining screws: 3.5 Nm (2.6 lb-ft). Refer to FSM for exact torque.
Critical Technical Points for Modified Engine
With a 63mm piston and racing camshaft, the stock ECU's fuel and ignition maps will be significantly off. Even with a perfectly calibrated TPS, the ECU will struggle to maintain stable idle due to:
- Increased valve overlap from the racing camshaft, leading to lower manifold vacuum at idle.
- Altered volumetric efficiency requiring different fuel delivery rates.
- The ECU's idle air control strategy is designed for the stock engine's airflow characteristics.
- The "breathing" idle symptom is highly indicative of the ECU attempting to correct an air-fuel imbalance beyond its adaptive limits.
- A standalone ECU or a reflash of the stock ECU with a custom tune is mandatory for proper operation and stable idle with these modifications.
Common Pitfalls
- Ignoring ECU Recalibration: The most significant pitfall is expecting the stock ECU to compensate for radical engine modifications. TPS adjustment alone will not resolve the underlying mapping issue.
- Incorrect TPS Alignment: If the TPS is adjustable, improper alignment can lead to incorrect throttle plate synchronization, affecting idle and off-idle performance.
- Harness Damage: Always inspect the TPS wiring harness for damage, chafing, or corrosion, especially after engine removal/installation or during modification.
- Vacuum Leaks: Re-verify for vacuum leaks around the intake manifold, throttle body, and any vacuum lines, as these will compound idle issues on a modified engine.
Special Tools Required
- Digital Multimeter: For static voltage and resistance checks.
- Diagnostic Scanner: Capable of reading live data streams (TPS voltage, throttle position percentage, fuel trims, RPM) for dynamic testing and verification.
- Vacuum Gauge: To assess manifold vacuum, which will be lower with a racing camshaft, but should still be stable.
Differential Diagnostics
- TPS Malfunction: Typically presents with erratic throttle response, specific DTCs (e.g., P0120, P0121), or a "limp mode." Voltage will be erratic or out of range.
- Idle Air Control (IAC) System Issues: Often causes hunting idle or stalling. The ECU commands the IAC valve based on TPS and other sensor inputs. If the ECU's base mapping is incorrect for the modified engine, it will mismanage the IAC.
- Vacuum Leaks: Leads to lean conditions and high, unstable idle. Can be identified with a smoke test.
- Fueling Issues (Modified Engine): Inadequate fuel delivery or incorrect injector pulse width for the increased displacement and airflow will cause lean conditions, leading to unstable idle. This points back to the need for ECU recalibration.
- Ignition Timing (Modified Engine): Incorrect ignition timing for the new camshaft profile and compression ratio will also cause rough, unstable idle.
TSBs and Recalls
- There are no specific Technical Service Bulletins or recalls pertaining directly to the Throttle Position Sensor or idle stability for the 2021 Yamaha Aerox 155cc with the stock engine configuration.
- Issues related to engine modifications are not covered by TSBs, as they fall outside OEM specifications.
These examples help guide a diagnosis. They do not confirm a fault on your vehicle: verify measurements and manufacturer specifications before repairing.