Diagnostic Code B3109, C0277, C0577 Chevrolet Suburban 2019 5.3L V8
Codes B3109, C0277, C0577 sur Chevrolet Suburban 2019 : symptômes, définitions, causes probables et vérifications prioritaires documentées par ChatMecano.
Symptômes observés
Im having trouble with the key fob, the range is very short. Also none of my tire pressures are registered
Codes OBD2 détectés
- B3109 — Code de défaut diagnostic standard constructeur
- C0277 — Code de défaut diagnostic standard constructeur
- C0577 — Code de défaut diagnostic standard constructeur
Analyse et vérifications ChatMecano
Les notes techniques reproduisent le dossier d’origine; certains extraits peuvent être rédigés dans la langue saisie par l’utilisateur.
Key Fob Short Range & TPMS Not Registering
These two issues, key fob range and TPMS sensor registration, are often related to the Remote Control Door Lock Receiver (RCDLR) module.
Likely Diagnosis
- Key Fob Short Range:
- Weak or dead key fob battery.
- Internal key fob damage.
- Radio Frequency (RF) interference.
- Faulty RCDLR module.
- No Tire Pressures Registered:
- Dead or failing TPMS sensor batteries (all four simultaneously is less common but possible).
- TPMS sensors not properly programmed to the vehicle.
- Faulty RCDLR module.
- Wiring issue to the RCDLR.
Given both issues are present, a shared component like the RCDLR module is a strong candidate for a common failure point.
Step-by-Step Procedure
- Check Key Fob Battery:
- Replace the key fob battery in all active fobs. Use a CR2032 coin cell battery.
- Test key fob range after replacement.
- Scan for Diagnostic Trouble Codes (DTCs):
- Connect an OBD-II scan tool.
- Check for codes in the Body Control Module (BCM) and RCDLR module (if accessible as a separate module).
- Look for codes related to RCDLR communication (e.g., B3109 for RCDLR performance) or TPMS (e.g., C0277 for TPMS sensor, C0577 for RCDLR internal fault).
- Perform TPMS Relearn Procedure:
- Ensure all tires are inflated to the placard pressure (38 PSI / 262 kPa).
- Access the TPMS relearn mode via the Driver Information Center (DIC) or using a scan tool.
- Follow the procedure to activate each sensor, starting with the front left, then front right, rear right, and rear left. A TPMS activation tool may be required.
- Verify if pressures register after successful relearn.
- Inspect RCDLR Module (if DTCs point to it):
- The RCDLR module is typically located in the headliner area, near the rear dome lamp, or behind the instrument panel.
- Inspect the module and its connectors for corrosion, damage, or loose connections.
- Check for power and ground at the RCDLR connector according to the FSM wiring diagrams.
- Test TPMS Sensors:
- Use a dedicated TPMS diagnostic tool to individually test each TPMS sensor for signal strength and battery status.
Torques & Specifications
- Key Fob Battery: CR2032.
- Tire Pressure: 38 PSI / 262 kPa (refer to door placard for exact vehicle specification).
OEM Parts / References
- Key Fob Battery: CR2032 type.
- TPMS Sensor: GM Part Number 13598773 (ref to verify).
- RCDLR Module: GM Part Number (varies by vehicle options, requires VIN for exact match, e.g., 84318080 or 84318081 ref to verify).
Common Pitfalls & Known TSBs
- RF Interference: Aftermarket accessories (dash cams, chargers, LED lights) can sometimes cause RF interference affecting key fob and TPMS signals.
- TPMS Relearn Errors: Ensure the correct sequence is followed during relearn. If using the DIC method, the horn chirps confirm successful sensor learning.
- TSB 16-NA-310: Addresses various key fob and RCDLR related issues, including range and programming. While dated, it indicates a history of RCDLR concerns. Review for applicability to your specific VIN.
- TSB 19-NA-087: Addresses TPMS sensor issues in some GM vehicles, including potential sensor battery degradation or programming difficulties. Review for applicability.
- RCDLR Software Update: In some cases, a software update for the RCDLR module via SPS programming may resolve communication issues. This requires a dealer-level scan tool.
Ces exemples aident à orienter un diagnostic. Ils ne confirment pas une panne sur votre véhicule : validez les mesures et spécifications du constructeur avant toute réparation.